Common Concerns About Horseshoes For Draft Horses Here in Waverly
# 1 – Aren’t Nanoflex horseshoe footwear slippery?
No matter just how a steed is shod, there is always danger connected with surfaces such as asphalt, wet turf as well as other examples of bad footing. That claimed, our shoes are commonly made use of turf training courses and also grass rings in the performance globe. In fact, several of our styles have stud attributes planned particularly for higher grip. In comparison, we have actually found Nanoflex footwear to be no more slippery than traditional footwear.
# 2 – I can see steel on the toe of my Nanoflex Horseshoes – is this typical?
The majority of our footwear comprises a wear plate in the toe region to assist eliminate excess wear on the shoe. If you look closely at most lightweight aluminum brands of footwear – you will certainly see the exact same thing. As your steed begins to use his shoe – the plate will certainly end up being extra visible. This attribute is an expected process within the shoeing cycle and is considered regular.
# 3 – Will Nanoflex Horseshoes fall off?
While all shoes have the possible ahead off, the success rate of our shoes remaining on rests entirely on the application process. As a matter of fact, with the right method and application – Nanoflex Horseshoes can be perfect for steeds with a tendency to draw footwear & will remain on also, otherwise much better than conventional footwear.
# 4 – Will my steed have the ability to put on Nanoflex footwear long-term?
Absolutely. While Nanoflex Horseshoes are not intended to be a long-term shoeing choice, they do use lots of advantages to the health and wellness of the steed’s foot. Many customers, as well as farriers, concur that they see increased horn development, structural integrity as well as sole depth after consistently utilizing Nanoflex.
# 5 – Can I shoe my steed with Nanoflex Horseshoes and also typical footwear concurrently?
Yes, actually it is common to have a horse putting on Nanoflex ahead & standard shoes in the back. What is important to remember is that every horse has various needs. What may function well for one steed might not function well for one more. Nanoflex Horseshoes are intended to be made use of in a selection of combinations that benefit each specific steed.
# 6 – When I footwear my equine in Nanoflex Horseshoes will I be able to switch back to traditional shoeing methods?
Most of the time, absolutely. Nanoflex Horseshoes are usually utilized as a way to an end to attain a particular therapeutic or affordable goal. Depending on your horse’s specific demands – it is fairly possible that your equine can go back to traditional shoeing methods. Periodically, we do have horses that grow in Nanoflex shoes, and also end up coming to be several of our long term consumers.
# 7 – If I can not locate the dimension or footwear I need for my equine, may I position a custom-made order/request?
Of our offered footwear, we provide a plethora of alternatives to best fulfill the requirements of as numerous horses as possible. Occasionally we do fulfill custom-made orders, however, we require payment for the store time and also products needed to develop specific modifications for the footwear. If your demand matches a personalized order we have actually had in the past, we may currently have the mold and mildew for it. If your request does not match any of our previous orders & is possible – creating a brand-new original footwear calls for considerably greater investment.
# 8 – I observed that not all Nanoflex Horseshoes coincide shade of brownish-yellow color – what does this mean?
Our footwear is made from raw material as well as these sets can sometimes have various shades. While their shade may not be identical, all of our shoes are of the very same top quality.
~ APPLYING NANOFLEX SHOES ~
# 1 – Why do you recommend that I utilize your kind of glue and sticky items for applying Nanoflex Horseshoes?
The what’s what is that we are not as concerned about brand name as we are about the quality of the product and also typically made use of. In time, as well as after much trial and error we have actually established a really details application procedure making use of products that we are positive in. We’ve had one of the most success with long-term bonds making use of a methacrylate blend glue with our unguis sealer – and also highly suggest using this type of glue in conjunction with our application directions for the best end results.
# 2 – Why do I require to blink dry the foot prior to applying Nanoflex footwear?
While it may really feel completely dry to the touch, the unguis is practically thought about wet after a fresh trim. If any kind of part of the hoof consists of wetness at the time of gluing, the sticky residential properties of the bond will be compromised. This is why we suggest flashing drying out the unguis with a torch before gluing on the footwear. To discover more in-depth directions, visit our Application Process web page to view a video tutorial as well as read our instructional short article.
# 3 – Can I use adhesive on footwear in weather extremes?
Yes, the secret is selecting the appropriate sort of adhesive, handling temperature of your adhesive and regulating your dampness degrees in the foot.
We like using fast set glue – nevertheless, if you are using glue on shoes for the very first time, the slow-moving collection will certainly give you a bigger time gap to prepare & use.
When trying to regulate the temperature level of your glue, attempt to stay clear of severe modifications. In cold weather – store your glue in a space temperature level environment & maintain your adhesive on a hot pad while you are preparing your foot. In heat extremes, saving your adhesive in a refrigerator & packaging your glue in a cooler will offer you good temperature level control also.
Finally, constantly remember to blink completely dry the foot using a lantern prior to applying the footwear. After a fresh trim, the steed’s hoof is taken into consideration wet. By flash drying out, you will certainly produce a suitable surface for your adhesive to bond to.
If you are mindful of these 3 things and also combine it with the proper application process you can get very good results shoeing in all weather condition kinds.
# 4 – What options do I have for shaping Nanoflex footwear?
Unlike typical footwear, our Nanoflex Horseshoes are made with an enveloped cable to allow for shaping. Additionally, our shoes are available in numerous toe sizes and alteration options to adjust to breed & discipline certain requirements.
That said, we do not encourage utilizing a hammer to shape Nanoflex Horseshoes. Our personal choice is to utilize the completion of a hoof jack to form the footwear. By placing the branch of the footwear that you are intending to form into the top of the aluminum blog post of your unguis jack (after eliminating the rubber cap that your hoof rests on) you are able to flex the shoe. By exaggerating the bend, you are normally able to accomplish the degree of change you are seeking.
If you require more support picking the appropriate footwear for your equine or creating the perfect fit, please call anytime for advice. In the meantime, be sure to sign in to see our upcoming instructional videos!
# 5 – Can Nanoflex Horseshoes be nailed on?
Yes and No, Nanoflex shoes are glue-able and nail-able. Because of the nature of their style, Nanoflex shoes can be used utilizing direct glue. If you were to toenail on a Nanoflex shoe, the all-natural flexibility of the polyurethane could produce enough excess motion to induce tension on the nails, therefore resulting in damages to the unguis wall surface.
# 6 – Exactly how do you get rid of a Nanoflex Horseshoe?
Our best recommendations are to deal with a Nanoflex shoe like an extension of the horse’s foot and also to cut it off. Nevertheless, bear in mind the glue to see to it you are not participating in the unguis off with your footwear.
# 7 – Can Nanoflex shoes be reset?
Nanoflex Horseshoes are implied to put on according to the steed’s natural footfall and are not intended to be utilized for greater than one shoeing. Depending on the discipline of your equine & the surfaces he/she is ridden on, the footwear will wear at different rates. We extremely suggest that you preserve your horse’s shoeing routine, and also do not extend the shoeing cycle.
# 8 – Exactly how do I locate even more information about the adhesive on the procedure?
We have additional sources for discovering our glue on the procedure on our web site under the “Horseshoes for Horses” tab. If you choose “Footwear” the fall food selection will supply you an “Application Process” choice. That page will certainly provide you a training video clip, detailed post and a web link to our Quarter Crack video clip. If those resources do not give you the responses you are seeking – please feel free to give us a call anytime. We are greater than pleased to assist you with any kind of questions about horseshoes or worries you might have.
Name: John Filipelli
Organization: Nanoflex, Inc.
Address: South Florida Trotting Center: 7563 State Road 7, Lake Worth FL 33449, USA
Phone: (954) 857-6337
Where to Find Horseshoes For Draft Horses in Waverly
Horse Hoof Care - No Hoof, No Horse
Horseshoe Studs, Caulks or Calks are metal devices that are screwed or driven into the bottom of your horse's shoes. By protruding from the bottom of the shoe, they can help to provide traction over muddy or deep footing, such as sand, and help your horse jump more confidently.
Before using studs, holes are "tapped," or drilled, into both heels, and sometimes the toes, of the horse's shoe. Obviously the size of the hole must accommodate the stud and generally in the US, farriers will tap a hole that supports a 3/8" diameter stud. Therefore, unless you have a special requirement for a smaller hole, such as a pony with very small feet, you should try to stick with 3/8' studs.
The first time you ride your horse with studs you should fit him with some small road studs and let him walk around unmounted for a while to get used to the new feeling (this does not mean turn him out in a field with studs in - horses should never be turned out in studs!)
Here are some simple rules for using studs. These relate to "screw-in" studs rather than "drive-in" studs because screw-in studs are by far the most commonly used types.
Do's: o ALWAYS use studs in pairs, with one on each side of the hoof.
o ALWAYS use small, blunt studs on the inside of your horse's shoes. A large, pointed stud can injure him.
o ALWAYS put protective leg boots on your horse when riding in studs.
o ALWAYS put studs in just before you will be riding and remove them as soon as possible afterwards.
o ALWAYS use the smallest stud you can, considering the conditions. While slipping is dangerous for your horse, a little slipping is much better than jarring your horse's legs with huge studs. Try to find a stud that allows a little slipping, but not so much that your horse's balance will suffer. Studs should be selected that will sink fully into the ground, otherwise they will unbalance the foot.
o ALWAYS try to have someone help you by holding your horse when you are putting studs in, especially if you will be using a Tee Tap (see below).
o ALWAYS be very careful if you have a horse that is likely to kick out at other horses or people. If you have such a horse, try to limit the amount of time you use studs.
Dont's: o NEVER turn your horse out with studs.
o NEVER leave your horse unattended in a stall with studs.
o NEVER trailer your horse with studs.
o NEVER use studs if your horse is lame.
o NEVER put yourself in a position where a horse with studs in can step on you. It is very easy to break a toe this way, even in riding boots.
Your Stud "Toolkit" Ahead of time, you should assemble the following items:
o A selection of studs. Remember that depending on the footing, you might not use the same studs on the inside and outside of your horse's shoes, or you could use different studs on the front than the back shoes. o A horseshoe nail or some type of flat but pointed "pick" to remove stud plugs. Screwdrivers are generally not suitable as they tend to be too "fat" to fit between the plug and the shoe.
o A stud hole cleaner. This is used to remove any debris from the stud hole. Some people use the horseshoe nail for this, but there are many specially-designed tools that will work faster.
o A tap of some type. This is used to clean and sharpen the edges of the threads your farrier drilled into the stud holes. There are many types on the market. The traditional type is a Tee Tap or T-Tap, so named because it is the shape of the letter "T". Recently round "Safety" Taps have become available on the market. These are safer because if your horse steps down on a Tee Tap it can cause an injury whereas a Safety Tap is less likely to cause a problem because it is flat and shaped like a hoof. There are some self-tapping studs starting to come onto the market that should remove the need for a separate Tap, however it is still a good idea to keep a Tap on hand.
o A wrench. This is used to tighten and then remove the studs. You can use a regular adjustable wrench found in most toolkits, although over time the wrench may wear the edges of your studs, making them difficult to use. There are also a number of special wrenches made specifically for horse studs. Even if you use a purpose-made wrench, it is probably not a bad idea to have an adjustable one too.
o A box to keep everything in one place! Studs have a notorious "homing" instinct and will disappear at the smallest opportunity. If you don't capture them in a box, you will never find them again next time you need them.
o Rags or a small sponge. For removing oil or grease from your studs (assuming you oiled and stored them correctly the last time you used them) Studs are definitely slippery when greasy and will jump on this opportunity as part of their escape plan!The following items are also nice to have: o A magnet for your arm or a magnetic dish. This is useful for keeping steel studs in one place while you work and will reduce the possibility of your studs escaping! o Rubber or cotton plugs or blanks. Most people put plugs in their stud holes when they are not using studs. This keeps the holes clean. There are rubber and cotton plugs and also metal stud blanks. If you use cotton plugs, soak them in oil to prevent the holes rusting. Stud blanks are metal screw-in plugs. If you use these, you will also need a....
o Blank Wrench or Flat-Head Screwdriver. A Blank Wrench is an Allen Key and is inserted into the stud blank to screw the blank in and out of the stud hole. Some stud blanks are designed to be inserted and removed using a Flat Head Screwdriver instead of a Blank Wrench.
o Stud cleaner and lubricant. Your studs will last much longer if you clean and grease them after use. Many people wrap them in an oily rag for storage, or you can use a product such as WD-40. Pretty much anything that repels water will work. There are also specially made stud cleaners available on the market.
Putting Studs in Ideally you should take a lesson from your farrier or trainer before attempting to put studs in yourself. Make sure you and your horse practice at home, until you can put them in and take them out easily, before using them at a competition. If your horse has plugs in his stud holes you will need to remove these first with your horseshoe nail or other implement.
HINT: It is a good idea to take the plugs out, clean the holes and replace the plugs before you leave for a competition. There is nothing more frustrating than not being able to remove a plug when you only have 10 minutes until you should be warming up your horse!Next you will need to clean out the stud hole with whatever tool you have chosen. Make sure that you remove all traces of dirt and debris. Putting studs into dirty stud holes can ruin the threads on your horse's shoes. Then (unless you are using self-tapping studs) you will need to tap the stud hole with a Safety Tap or Tee Tap. Unless you have a very quiet, experienced horse and are experienced with studs, we recommend using a Safety Tap. Basically, you will place the end of the Tap into the stud hole and screw it into the hole. Another benefit of a Safety Tap is that you can't screw the Tap in too far and potentially bruise your horse's hoof, which is possible with a Tee Tap.
HINT: Self-tapping studs are a new option where the stud has a special thread that will clean the threads on your horse's shoes as you insert it. Because they are new, these studs are more expensive than traditional studs, but as long as you don't lose them, they could be a great timesaving investment. Now you can insert the studs. Begin by screwing them in by hand and finally make them nice and tight with your wrench. Be sure that you don't over-tighten them so that you can't undo them after you finish riding!When you are finished riding, remove the studs, plug the holes and store the studs in some form of oily rag or plastic bag with a water repellent - any kind of oil, grease or WD-40 will work. Make sure you keep some rags or a sponge on hand to wipe up the grease! Put your studs back in their box - if you don't they WILL escape!!! And don't forget to have a great ride!
For more information on types of studs and when to use them, please visit www.StudsAndStuff.com