Horseshoes For Sale in Illinois

Horseshoes For Sale

Information on Horseshoes For Sale in  Illinois

Therapeutic Shoes For Horses

How Often Should You Shoe Your Horse? The Real Deal on Hoof Steel

A basic part of horse hoof care is simply picking out the mud, manure, stones and other debris from the sole of your horse's hooves. It is simple and yet, this one of the most neglect parts of horse care. Keeping your horse's hooves clean goes a long way to help prevent common hoof ailments. At times, your horse may get small stones lodged in the grooves of the frog, which can cause bruising. Picking out your horse's hooves also removes packed mud or snow, which can make it uncomfortable for your horse to walk. Cleaning your horse's feet will allow you to see problems such as a puncture wound from something like a nail.

You will certainly hear or read from horsemen recommending you pick your horse's feet at least once daily, as well as before and after a ride. This is no doubt good advice, but in practical terms, don't go longer than a week without cleaning and inspecting your horse's hooves.

Keeping your horse's feet clean and dry as much as possible helps prevent thrush. The flooring of the stable should not be damp and allow for drainage. Your horse's paddock area should provide drainage to minimize the amount of time he has to stand in water and mud. Most of the moisture your horse's hooves need come from within the hoof itself and is provided by a healthy diet. Constant contact with wet conditions promotes rapid drying of the hooves and will cause them to start cracking and chipping.

Applying a hoof dressing can improve the moisture content of hooves and help prevent them from cracking. Rubbing hoof dressing on all parts of the hoof including the hoof wall, frog, heel and coronet can stimulate healthy new hoof growth. However, you should not apply hoof dressing too often as it may prevent the hooves from absorbing moisture naturally.

In the wild, a horse's feet wear down about the same rate as they grow. A domestic horse's hooves typically do not wear down as quickly since their hooves may be shod preventing them from wearing naturally, or simply because they are not subjected to such severe living conditions and consequently their feet grow faster than can be worn down.

In general, hooves need to be trimmed every six to eight weeks requiring the routine care of a professional farrier. The services of a reliable and experienced farrier are vital to helping keep your horse's hooves healthy. When choosing a farrier, ask other horse owners in your area and your veterinarian for a recommendation. Do not wait until you need a farrier before trying to find one.

Your farrier can help you decide whether or not your horse needs to be shod. Horses that are ridden a lot or work on hard terrain may need horseshoes or boots to protect their hooves. If your horse's hooves wear too much, the protective outer covering starts to be lost and the foot can become sensitive causing lameness. On the other hand, if your horse is more of a field ornament to be looked at or is only ridden occasionally then he most likely doesn't need to be shod. Regardless if your horse is shod or not, his hooves will need regular trimming to keep them shaped properly.

Without regular trimming, a horse's hooves will grow too long and can lead to hoof splitting, chipping, cracking and lameness. Long hooves can put your horse's leg limbs out of balance. Hooves need to be trimmed to keep them at the correct length and shape so contact with the ground will be uniform and will not cause the hoof to chip or split. Shod horses especially need a farrier's attention on a regular basis due to hoof growth loosening the shoes and growing over the edge of the shoes.

# 1 – What are Nanoflex Horseshoes, and how do they function?

Nanoflex Horseshoes are a shapable polyurethane straight glue on shoe that resembles the natural make-up as well as put on qualities of the hoof. Our footwear are commonly used in performance and also restorative situations as an alternative application with horses that become unresponsive to conventional shoeing techniques.

With their capability to resemble the technician residential or commercial properties of the foot – Nanoflex Horseshoes boost the feature of the hoof, instead of limiting it. This commonly leads to a much more comfortable equine with healthier development.

# 2 – What are the benefits of Nanoflex shoes?

Nanoflex footwear supply several advantages for the steed. Most typically, we listen to customers describing the shoes ability to operate as an all-natural extension of the unguis as the most desirable attribute. The direct glue application together with the shoe’s composition are thought to preserve the regular hoof features of assistance, traction, shock absorption as well as proprioception by bending with the unguis.

In our opinion, traditional adhesive on footwear over long term use tend to reverse the preliminary benefits attained because of the casting nature of an inflexible footwear. In contrast, our observations have found Nanoflex shoes to be successful for long term use and also appear to produce much healthier horn development.

# 3 – How much time will the Nanoflex shoes last?

Nanoflex Horseshoes are created to have the same or comparable life expectancy as typical footwear. We advise shoeing your horse according to the ordinary cycle of 4-6 weeks, based on their personal demands.

# 4 – Are Nanoflex footwear much more costly than conventional shoes?

Yes. The moment it takes to produce our shoes, in addition to the materials as well as craftsmanship required for the application procedure makes Nanoflex Horseshoes a true investment.

# 5 – What makes an equine an excellent prospect for Nanoflex horseshoes?

Under our “Shoes” tab, you will certainly find “Selecting A Candidate” alternative in the drop down menu. If you see this web page you will certainly find a comprehensive description of the 4 main factors we take into consideration before determining if a horse is a Nanoflex prospect.

Company Information:

Name: John Filipelli

Email: sales@nanoflexinc.com

Organization: Nanoflex, Inc.

Address: South Florida Trotting Center: 7563 State Road 7, Lake Worth FL 33449, USA

Phone: (954) 857-6337

Monday

8AM–7PM

Tuesday

8AM–7PM

Wednesday

8AM–7PM

Thursday

8AM–7PM

Friday

8AM–7PM

Saturday

10AM–5PM

Sunday

12AM–5PM

Find Horseshoes For Sale in the State of Illinois


Where to find information about Horseshoes For Sale in Illinois

Farriers Horses Lameness And The Natural Balance Shoe A Case Study

horseshoes for navicular horses

Horseshoe Studs, Caulks or Calks are metal devices that are screwed or driven into the bottom of your horse's shoes. By protruding from the bottom of the shoe, they can help to provide traction over muddy or deep footing, such as sand, and help your horse jump more confidently.

Before using studs, holes are "tapped," or drilled, into both heels, and sometimes the toes, of the horse's shoe. Obviously the size of the hole must accommodate the stud and generally in the US, farriers will tap a hole that supports a 3/8" diameter stud. Therefore, unless you have a special requirement for a smaller hole, such as a pony with very small feet, you should try to stick with 3/8' studs.

The first time you ride your horse with studs you should fit him with some small road studs and let him walk around unmounted for a while to get used to the new feeling (this does not mean turn him out in a field with studs in - horses should never be turned out in studs!)

Here are some simple rules for using studs. These relate to "screw-in" studs rather than "drive-in" studs because screw-in studs are by far the most commonly used types.


Do's: o ALWAYS use studs in pairs, with one on each side of the hoof.

o ALWAYS use small, blunt studs on the inside of your horse's shoes. A large, pointed stud can injure him.

o ALWAYS put protective leg boots on your horse when riding in studs.

o ALWAYS put studs in just before you will be riding and remove them as soon as possible afterwards.

o ALWAYS use the smallest stud you can, considering the conditions. While slipping is dangerous for your horse, a little slipping is much better than jarring your horse's legs with huge studs. Try to find a stud that allows a little slipping, but not so much that your horse's balance will suffer. Studs should be selected that will sink fully into the ground, otherwise they will unbalance the foot.

o ALWAYS try to have someone help you by holding your horse when you are putting studs in, especially if you will be using a Tee Tap (see below).

o ALWAYS be very careful if you have a horse that is likely to kick out at other horses or people. If you have such a horse, try to limit the amount of time you use studs.



Dont's: o NEVER turn your horse out with studs.

o NEVER leave your horse unattended in a stall with studs.

o NEVER trailer your horse with studs.

o NEVER use studs if your horse is lame.

o NEVER put yourself in a position where a horse with studs in can step on you. It is very easy to break a toe this way, even in riding boots.


Your Stud "Toolkit" Ahead of time, you should assemble the following items:
o A selection of studs. Remember that depending on the footing, you might not use the same studs on the inside and outside of your horse's shoes, or you could use different studs on the front than the back shoes. o A horseshoe nail or some type of flat but pointed "pick" to remove stud plugs. Screwdrivers are generally not suitable as they tend to be too "fat" to fit between the plug and the shoe.

o A stud hole cleaner. This is used to remove any debris from the stud hole. Some people use the horseshoe nail for this, but there are many specially-designed tools that will work faster.

o A tap of some type. This is used to clean and sharpen the edges of the threads your farrier drilled into the stud holes. There are many types on the market. The traditional type is a Tee Tap or T-Tap, so named because it is the shape of the letter "T". Recently round "Safety" Taps have become available on the market. These are safer because if your horse steps down on a Tee Tap it can cause an injury whereas a Safety Tap is less likely to cause a problem because it is flat and shaped like a hoof. There are some self-tapping studs starting to come onto the market that should remove the need for a separate Tap, however it is still a good idea to keep a Tap on hand.

o A wrench. This is used to tighten and then remove the studs. You can use a regular adjustable wrench found in most toolkits, although over time the wrench may wear the edges of your studs, making them difficult to use. There are also a number of special wrenches made specifically for horse studs. Even if you use a purpose-made wrench, it is probably not a bad idea to have an adjustable one too.

o A box to keep everything in one place! Studs have a notorious "homing" instinct and will disappear at the smallest opportunity. If you don't capture them in a box, you will never find them again next time you need them.

o Rags or a small sponge. For removing oil or grease from your studs (assuming you oiled and stored them correctly the last time you used them) Studs are definitely slippery when greasy and will jump on this opportunity as part of their escape plan!

The following items are also nice to have: o A magnet for your arm or a magnetic dish. This is useful for keeping steel studs in one place while you work and will reduce the possibility of your studs escaping! o Rubber or cotton plugs or blanks. Most people put plugs in their stud holes when they are not using studs. This keeps the holes clean. There are rubber and cotton plugs and also metal stud blanks. If you use cotton plugs, soak them in oil to prevent the holes rusting. Stud blanks are metal screw-in plugs. If you use these, you will also need a....

o Blank Wrench or Flat-Head Screwdriver. A Blank Wrench is an Allen Key and is inserted into the stud blank to screw the blank in and out of the stud hole. Some stud blanks are designed to be inserted and removed using a Flat Head Screwdriver instead of a Blank Wrench.

o Stud cleaner and lubricant. Your studs will last much longer if you clean and grease them after use. Many people wrap them in an oily rag for storage, or you can use a product such as WD-40. Pretty much anything that repels water will work. There are also specially made stud cleaners available on the market.


Putting Studs in Ideally you should take a lesson from your farrier or trainer before attempting to put studs in yourself. Make sure you and your horse practice at home, until you can put them in and take them out easily, before using them at a competition. If your horse has plugs in his stud holes you will need to remove these first with your horseshoe nail or other implement.


HINT: It is a good idea to take the plugs out, clean the holes and replace the plugs before you leave for a competition. There is nothing more frustrating than not being able to remove a plug when you only have 10 minutes until you should be warming up your horse!Next you will need to clean out the stud hole with whatever tool you have chosen. Make sure that you remove all traces of dirt and debris. Putting studs into dirty stud holes can ruin the threads on your horse's shoes. Then (unless you are using self-tapping studs) you will need to tap the stud hole with a Safety Tap or Tee Tap. Unless you have a very quiet, experienced horse and are experienced with studs, we recommend using a Safety Tap. Basically, you will place the end of the Tap into the stud hole and screw it into the hole. Another benefit of a Safety Tap is that you can't screw the Tap in too far and potentially bruise your horse's hoof, which is possible with a Tee Tap.


HINT: Self-tapping studs are a new option where the stud has a special thread that will clean the threads on your horse's shoes as you insert it. Because they are new, these studs are more expensive than traditional studs, but as long as you don't lose them, they could be a great timesaving investment. Now you can insert the studs. Begin by screwing them in by hand and finally make them nice and tight with your wrench. Be sure that you don't over-tighten them so that you can't undo them after you finish riding!When you are finished riding, remove the studs, plug the holes and store the studs in some form of oily rag or plastic bag with a water repellent - any kind of oil, grease or WD-40 will work. Make sure you keep some rags or a sponge on hand to wipe up the grease! Put your studs back in their box - if you don't they WILL escape!!! And don't forget to have a great ride!

For more information on types of studs and when to use them, please visit www.StudsAndStuff.com